回轉風機日常維護及保養事項：

Routine maintenance and care of rotary fan:

1.潤滑系統的檢查回轉風機嚴禁缺油運轉

1. Inspection of lubrication system: the rotary fan shall not run without oil

1、檢查油箱內的潤滑油是否低于zui低油位，如儲油量不足請加油建議用68#液壓油，低溫寒冷地區可適當降低機油牌號。

1. Check whether the lubricating oil in the oil tank is lower than Zui low oil level. If the oil storage is insufficient, please add oil. It is recommended to use 68 # hydraulic oil. In low-temperature and cold areas, the oil grade can be appropriately reduced.

2、檢查機油是否混入水份等污物而變質，如變質請及時更換機油。

2. Check whether the engine oil is deteriorated due to water and other dirt. If it is deteriorated, please replace the engine oil in time.

3、清洗油過濾器，如太臟請及時更換。

3. Clean the oil filter. If it is too dirty, please replace it in time.

4、檢查滴油嘴的滴油狀況是否正常，如滴油嘴臟了可卸下調整螺釘清洗。

4. Check whether the oil dripping condition of the oil drip nozzle is normal. If the oil drip nozzle is dirty, remove the adjusting screw for cleaning.

2、保持風機房環境衛生，周邊無油污或雜質，保持良好通風很關鍵。

2. It is very important to keep the environment of the fan room clean and free of oil stain or impurities, and maintain good ventilation.

3、空氣濾清器的檢查，如臟了可卸下空氣濾清器，旋開蝶型螺母，拿開蓋子，清洗過濾海綿如太臟請及時更換卸濾清器時注意不要把臟物掉進風機主機內。

3. Check the air filter. If it is dirty, remove the air filter, unscrew the butterfly nut, remove the cover, and clean the filter sponge. If it is too dirty, please replace it in time. When removing the filter, be careful not to drop dirt into the fan main body.

4、檢查風機有無漏油、漏氣的部位，如有這種情況，請及時維修，或及時聯系生產廠家來進行專業維修。

4. Check whether there is oil or air leakage in the fan. If so, please repair it in time or contact the manufacturer for professional maintenance.

5、皮帶的檢查，風機運行一段時間后，皮帶會松弛會伸長或破損，如松弛要將電機的固定螺栓松開，移動電機，拉緊三角帶到合適位置后再將電機固定螺栓緊住，并注意電機皮帶輪和風機皮帶輪的端面要在同一平面上，同時檢查一下兩皮帶輪的頂緊螺絲是否松掉，如松了請緊住。

5. Inspection of the belt: after the fan runs for a period of time, the belt will be loose, elongated or damaged. If it is loose, loosen the fixing bolts of the motor, move the motor, tighten the V-belt to a proper position, and then tighten the fixing bolts of the motor. Note that the end faces of the motor pulley and the fan pulley should be on the same plane. At the same time, check whether the top screws of the two pulleys are loose. If they are loose, please tighten them.

6、經常檢查安全閥的靈活狀況，如不靈活請清洗調試以保證可靠的啟閉。

6. Frequently check the flexibility of the safety valve. If it is not flexible, please clean and debug it to ensure reliable opening and closing.

7、檢查風機及電機的運行狀況，如發現異常震動或噪音、溫度不正常時要及時停機檢修，找出故障原因及相應處理方法。

7. Check the operation condition of the fan and motor. In case of abnormal vibration, noise and temperature, stop the machine for maintenance in time to find out the cause of the fault and the corresponding treatment methods.

回轉風機主要用途：一、各種工業污水或廢水處理鼓風曝氣 二、醫院或實驗室、生活污水的污水攪拌曝氣 三、印刷行業的真空送紙 四、塑焊、吹風的氣源供應 六、燃燒器的噴霧、玻璃工業 七、 需要氣源的其他設備

Main uses of rotary fan: 1. Blowing and aeration for various industrial sewage or wastewater treatment; 2. Sewage mixing and aeration for hospitals or laboratories and domestic sewage; 3. Vacuum paper feeding for printing industry; 4. Air supply for plastic welding and blowing; 6. Spray for burners and glass industry; 7. Other equipment requiring air supply

以上就是為大家介紹的有關甘肅回轉風機廠家的詳細的介紹,希望對您有所幫助.如果您有什么疑問的話,歡迎聯系我們.我們將以專業的態度,為您提供服http://www.makemoore.com

The above is the detailed introduction of Gansu rotary fan manufacturers. I hope it will help you. If you have any questions, please contact us. We will provide services for you with a professional attitude http://www.makemoore.com

相關文章： 陜西離心式風機廠家 凈化器 氣力輸送設備廠家 油煙 甘肅回轉風機廠家