不知道大家有沒有了解過回轉風機廠家呢,知道回轉風機碰撞受損的解決辦法嗎,下面我們就一起來看看吧,望大家在百忙之中一起閱讀理解一下吧?;剞D風機由主機,底座,電機,大小皮帶輪,空氣室,空氣過濾器,滴油嘴等部件組成。


">

歡迎您光臨山東宇淇通成環保設備有限公司官方網站! 主營業務:氣力輸送設備廠家,山西羅茨風機廠家
..
環保設備供應商 專注氣力輸送系統氣體處理
服務咨詢電話:13276418636

講述回轉風機碰撞受損的解決辦法?

文章來源: 作者:羅茨機電 發布時間:2021-06-08 瀏覽次數:730

返回: 新聞中心

不知道大家有沒有了解過回轉風機廠家呢,知道回轉風機碰撞受損的解決辦法嗎,下面我們就一起來看看吧,望大家在百忙之中一起閱讀理解一下吧?;剞D風機由主機,底座,電機,大小皮帶輪,空氣室,空氣過濾器,滴油嘴等部件組成。

I don't know if you have known about the manufacturer of rotary fan and the solution to the collision damage of rotary fan. Let's have a look. I hope you can read and understand it together in your busy schedule. The rotary fan is composed of main machine, base, motor, pulley, air chamber, air filter, oil dripping nozzle, etc.

甘肅回轉風機廠家主機由鑄鐵澆鑄而成,金屬環2只,或彈簧8根,主機軸1根,轉子1只,滑片4只,偏心缸體1只,泵蓋2只組成,其中風機金屬環,轉子,滑片,泵蓋及偏心缸體由耐磨鑄件制造,主機軸由45號鋼材制造。

The main engine of Gansu rotary fan manufacturer is made of cast iron, including 2 metal rings, 8 springs, 1 main engine shaft, 1 rotor, 4 slides, 1 eccentric cylinder block and 2 pump covers. The metal rings, rotors, slides, pump covers and eccentric cylinder blocks of the fan are made of wear-resistant castings, and the main engine shaft is made of 45 steel.

          甘肅回轉風機廠家

回轉風機4根滑片嵌入在等分的轉子內,回轉風機軸緊固在轉子中心,軸的兩端裝有軸承與前后泵蓋連接安裝在偏心的缸體上,此時轉子與4根嵌入在轉子內的滑片與缸體內壁形成4個容積不等的空間,在回轉風機運行過程中,金屬環或彈簧推動滑片沿缸體內壁勻速運動,回轉風機缸體由吸入口,吸氣口導氣槽,排氣口,排氣口導氣槽組成?;剞D風機的工作過程由:吸氣行程,壓縮行程,排出行程三部分組成?;剞D風機旋轉時,使轉子槽內的4根滑片產生往復運動,將空氣吸進、壓縮、排出,構成風機。

Four slides of the rotary fan are embedded in the equally divided rotor. The shaft of the rotary fan is fixed in the center of the rotor. Bearings are installed at both ends of the shaft, which are connected with the front and rear pump covers and installed on the eccentric cylinder block. At this time, the rotor, the four slides embedded in the rotor and the inner wall of the cylinder block form four spaces with different volumes. During the operation of the rotary fan, the metal ring or spring pushes the slides to move uniformly along the inner wall of the cylinder, The cylinder body of rotary fan is composed of suction port, suction port air guide groove, exhaust port and exhaust port air guide groove. The working process of rotary fan consists of three parts: suction stroke, compression stroke and discharge stroke. When the rotary fan rotates, the four slides in the rotor slot produce reciprocating motion, and the air is sucked in, compressed and discharged to form the fan.

回轉風機受碰撞后,可能引起風機轉子靠偏,風機運轉不靈,可松開螺栓,輕敲見機后蓋,同時拉動風機皮帶直到能拉動風機皮帶、無輕重感為止?;剞D風機受碰撞后,可能引起風機轉子靠偏,風機運轉不靈?;剞D風機如發生碰撞事故,首先用手拉一下風機皮帶,試一下風機是否能正常轉動,如風機能正常轉動,無輕重感,則風機無故障現象。如風機不能拉動,或能拉動但有輕重感,則說明風機轉子靠偏,此時可松開后蓋螺栓,用木錘輕輕敲打風機后蓋,同時拉動風機皮帶,直到能拉動風機皮帶、無輕重感為止,再擰緊后蓋即可。

After the rotary fan is collided, the rotor of the fan may deviate and the fan may not work properly. Loosen the bolts, tap the back cover of the fan, and pull the fan belt until the fan belt can be pulled and there is no sense of weight. After the rotary fan is collided, the rotor of the fan may be deviated and the fan may not work properly. In case of collision accident of rotary fan, first pull the fan belt by hand to test whether the fan can rotate normally. If the fan can rotate normally and has no sense of weight, the fan has no fault. If the fan can't be pulled, or can be pulled but has light and heavy feeling, it means that the rotor of the fan is leaning. At this time, loosen the bolts of the back cover, gently tap the back cover of the fan with a wooden hammer, and pull the fan belt at the same time until the fan belt can be pulled without light and heavy feeling, and then tighten the back cover.

感謝您的閱讀,希望以上內容能對您有所幫助,如您想了解更多精彩內容請點擊我們的官網:甘肅回轉風機廠家。

Thank you for reading, hope the above content can help you, if you want to know more wonderful content, please click our official website: Gansu rotary fan manufacturer.


相關文章: 陜西離心式風機廠家 凈化器 氣力輸送設備廠家 油煙 甘肅回轉風機廠家

开心久久婷婷综合中文字幕,看av片,看黄片的视频,看黄片免费