甘肅回轉風機廠家的回轉風機被廣泛應用，但是回轉風機生銹該怎么處理和使用過程中怎樣保證氣缸內的氣體不回流呢，今天由小編給大家介紹一下吧。

Gansu rotary fan manufacturer's rotary fan is widely used, but how to deal with the rust of the rotary fan and how to ensure that the gas in the cylinder does not return in the process of use? Today, let's introduce it by the editor.

回轉風機生銹的處理方式，回轉風機是一種靠容積變化而工作的鼓風機產品，由于風機在運行時，兩個葉輪始終都是不接觸的。這也就是說，不會產生磨損，由于兩個葉輪之間的間隙非常小，所以不能有異物在里面，這樣會導致風機停止運轉。

Rotary fan rust treatment, rotary fan is a rely on volume change and work of the blower products, because the fan in operation, the two impellers are always not in contact. That is to say, there will be no wear, because the gap between the two impellers is very small, so there should be no foreign matter in it, which will cause the fan to stop running.

但是甘肅回轉風機廠家主要用于污水處理，養殖等場合，由于維護不到位，往往會使風機內部生銹，這樣就減小了兩葉輪之間的間隙，出現卡死現象，使風機停止運轉，這是就需要對回轉風機的內部葉輪進行除銹處理。

However, Gansu rotary fan manufacturers are mainly used for sewage treatment, breeding and other occasions. Due to the inadequate maintenance, the internal rust of the fan is often caused, which reduces the gap between the two impellers and causes the fan to stop running. This requires derusting the internal impeller of the rotary fan.

好的方法就是拆開用砂紙打磨，然后再進行安裝即可。由于風機在安裝時對間隙要求比較嚴格，一般是是0.05至0.1毫米之間，所以沒有專業人員指導的情況下，不要自己拆裝。

A good way is to take it apart, grind it with sandpaper, and then install it. Due to the fan in the installation of the clearance requirements are relatively strict, generally between 0.05 to 0.1 mm, so there is no professional guidance, do not disassemble.

回轉式鼓風機靠汽缸內偏置的轉子偏心運轉，并使轉子槽中的葉片之間的容積變化將空氣吸入、壓縮、吐出。在運轉中利用鼓風機的壓力差自動將潤滑送到滴油嘴，滴入汽缸內以減少摩擦及噪聲，同時可保持汽缸內氣體不回流?；剞D風機在設備通氣前的檢測時運行注意事項正式通水前，先進行回轉風機通氣檢測，通氣前先啟動風機，開啟風機風量的百分之五十，送至生化池曝氣管道中檢測，檢查管道所有節點焊接安裝質量，不能有漏氣現象發生，不易檢測時應用肥皂水進行檢測。此時，風機運轉特別注意，比如風機不能空載運行，風機潤滑油在沒有壓力時，潤滑油不能自動循環使用，風機有缺油運行的風險，因此在試漏檢測時，要不斷的從進風口加適量潤滑油讓風機正常運轉。

The rotary blower relies on the eccentric operation of the offset rotor in the cylinder, and makes the volume change between the blades in the rotor slot to suck in, compress and eject the air. During the operation, the pressure difference of the blower is used to automatically send the lubrication to the oil dripping nozzle and drop it into the cylinder to reduce the friction and noise, while keeping the gas in the cylinder from returning. Before ventilation, start the fan, turn on 50% of the air volume of the fan, and send it to the aeration pipe of the biochemical tank for detection. Check the welding and installation quality of all nodes of the pipe, and no air leakage is allowed. When it is difficult to detect, use soapy water for detection. At this time, special attention should be paid to the operation of the fan. For example, the fan can't run without load, the lubricating oil can't be recycled automatically when there is no pressure, and the fan has the risk of oil shortage operation. Therefore, during the leakage test, it is necessary to continuously add an appropriate amount of lubricating oil from the air inlet to make the fan operate normally.

本文由甘肅回轉風機廠家整理提供，感謝您的閱讀，希望以上內容對您有所幫助，如您想了解更多精彩內容請點擊我們的官網：http://www.makemoore.com。

This article is provided by Gansu rotary fan manufacturer. Thank you for your reading. I hope the above contents can help you. If you want to know more wonderful contents, please click our official website: http://www.makemoore.com .

相關文章： 陜西離心式風機廠家 凈化器 氣力輸送設備廠家 油煙 甘肅回轉風機廠家